使用串口连接 （参数跟V490等一样）
login: admin （默认账号登陆，无密码）
XSCF>
XSCF>
Display all 139 possibilities (y or n) （按两下Tab键显示SC下所有的命令）
（此处省略）
XSCF> showhardconf –u （显示硬件信息）
SPARC Enterprise M5000; Memory_Size:16 GB;
（此处省略）
XSCF> adduser eis-installer （新建账号）
XSCF> setprivileges eis-installer platadm useradm auditadm fieldeng mode (为用户提供适当的特权)
XSCF> setprivileges fieldeng fieldeng mode
XSCF> password eis-installer （新建账号设置密码）
New XSCF password:
BAD PASSWORD: it is too short
Retype new XSCF password:
XSCF> exit
logout
login:
login: eis-installer
Password:
XSCF>
XSCF>
XSCF>
XSCF> showuser -l
User Name: eis-installer
UID: 100
Status: Enabled
Minimum: 0
Maximum: 99999
Warning: 7
Inactive: -1
Last Change: Nov 11, 2008
Password Expires: Never
Password Inactive: Never
Account Expires: Never
Privileges: useradm
platadm
mode
fieldeng
auditadm
XSCF>
XSCF> poweron -d 0 （给主机Domain 0加电）
DomainIDs to power on:00
Continue [y|n] :y
00 :Powering on
*Note*
This command only issues the instruction to power-on.
The result of the instruction can be checked by the "showlogs power".
XSCF>
XSCF>
XSCF> console -d 0 （进入Console）
Connect to DomainID 0[y|n] :y
{0} ok
{0} ok
客户没有要求做Domain，机器硬件默认在Domain0，以上的步骤是装系统之前的简单操作，下面是配置管理网络端口，xscf能够配置两个端口，本例是配置lan#0的步骤。（注意两个端口的IP不能是同一网段）配置好后可以通过此网口telnet XSCF。
XSCF> setupplatform
Do you want to set up an account [y|n]: n
Do you want to set up networking [y|n]: y
Do you want to set up the XSCF network interfaces [y|n]: y
Do you want to configure xscf#0-lan#0 [y|n]: y
xscf#0-lan#0 ip address []: 10.151.162.32
xscf#0-lan#0 netmask [255.255.255.0]:
xscf#0-lan#0 default gateway []: XSCF> setupplatform
Do you want to set up an account [y|n]: n
Do you want to set up networking [y|n]: y
Do you want to set up the XSCF network interfaces [y|n]: y
Do you want to configure xscf#0-lan#0 [y|n]: y
xscf#0-lan#0 ip address []: 10.151.162.30
xscf#0-lan#0 netmask [255.255.255.0]:
xscf#0-lan#0 default gateway []: 10.151.162.254
xscf#0-lan#0 ip address: 10.151.162.30
xscf#0-lan#0 netmask: 255.255.255.0
xscf#0-lan#0 default gateway: 10.151.162.254
Are these settings correct [y|n]: y
XSCF> setnetwork xscf#0-lan#0 -m 255.255.255.0 10.151.162.30
XSCF> setroute -c add -n 0.0.0.0 -m 0.0.0.0 -g 10.151.162.254 xscf#0-lan#0
Do you want to configure xscf#0-lan#1 [y|n]: n
Do you want to configure lan#0 [y|n]: y
lan#0 ip address []: 10.151.162.30
lan#0 netmask [255.255.255.0]:
lan#0 ip address: 10.151.162.30
lan#0 netmask: 255.255.255.0
Are these settings correct [y|n]: y
XSCF> setnetwork lan#0 -m 255.255.255.0 10.151.162.30
Do you want to configure lan#1 [y|n]: n
Do you want to set up the DSCP network [y|n]: y
DSCP network []: 10.151.162.0
DSCP netmask [255.255.255.0]:
DSCP network: 10.151.162.0
DSCP netmask: 255.255.255.0
Are these settings correct [y|n]: y
XSCF> setdscp -q -y -i 10.151.162.0 -m 255.255.255.0
Domain name service is already configured:
Primary DNS server ip address:
Secondary DNS server ip address:
Tertiary DNS server ip address:
Domain name: localdomain
XSCF#0 hostname: localhost
Do you want to set up the domain name service [y|n]: y
Primary DNS server ip address []: 192.168.1.1
Do you want a secondary DNS server [y|n]: n
Do you want to specify a domain name [y|n]: y
Domain name [localdomain]: Domain0
XSCF#0 hostname [localhost]: JYRLDB
Primary DNS server ip address: 192.168.1.1
Secondary DNS server ip address:
Tertiary DNS server ip address:
Domain name: Domain0
XSCF#0 hostname: JYRLDB
Are these settings correct [y|n]: y
XSCF> setnameserver -c del -a
XSCF> setnameserver -c add 192.168.1.1
XSCF> sethostname xscf#0 JYRLDB
XSCF> sethostname -d Domain0
Do you want to set up the network time protocol [y|n]: n
The ssh service is: disabled
Do you want to set up ssh [y|n]: n
The https service is: disabled
Do you want to set up https [y|n]: n
Do you want to configure email reports [y|n]: n
Do you want to apply the network changes [y|n]: y
XSCF> applynetwork -y
The following network settings will be applied:
xscf#0 hostname :JYRLDB
DNS domain name :Domain0
nameserver :192.168.1.1
interface :xscf#0-lan#0
status :up
IP address :10.151.162.30
netmask :255.255.255.0
route :-n 0.0.0.0 -m 0.0.0.0 -g 10.151.162.254
interface :xscf#0-lan#1
status :down
IP address :
netmask :
route :
Continue [y|n] :y
相关文章：Sun SPARC Enterprise M5000产品特性及规格
